Programming the Remote
Programmed Device FunctionsNotes on Using the AVR5000 Volume Punch-Through
Remote With Other Devices.
Once the AVR5000Os remote has been pro-The AVR5000Os remote may be programmed to
Y Manufacturers may use different code sets for
grammed for the codes of other devices, press thethe same product category. For that reason, it isoperate the Volume Control $ and the Mute
appropriate Input Selector 4 to change theimportant that you check to see if the code set from either the TV or the AVR in conjunction
remote from control over the AVR5000 to thewith any of the six devices controlled by the
you have entered operates as many controls as
additional product.When you press any of thesepossible. If it appears that only a few functionsremote. For example, since the AVR5000 will likely
buttons, it will briefly flash in red to indicate thatbe used as the sound system for TV viewing, you
operate, check to see if another code set will
you have changed the device being controlled.work with more buttons.may wish to have the AVROs volume activated
although the remote is set to run the TV.
When operating a device other than theY Depending on the brand and product type used
AVR5000, the controls may not correspond exact-To program the remote for Volume Punch-
ly to the function printed on the remote or but-the functions listed in the Function List tablesThrough, follow these steps:
may not correspond with the function the unit
ton. Some commands, such as the volume con-reacts on the command. In these cases itOs a1. Press the Input Selector 4 for the unit you
trol, are the same as they are with the AVR5000.
good idea to edit the reaction of the unit into thewish to have associated with the volume control
Other buttons will change their function so thatcorresponding line of the table or to set up aand the Mute button at the same time until
they correspond to a secondary label on theseparate list.the red light illuminates under the Input Selector
remote. For example, the Sleep and Surround
4 and note that the Program/SPL Indicator
mode selector buttons also function as theY When a button is pressed on the AVR50002 will flash amber.
Channel Up and Channel Down buttons whenremote, the red light under the Input Selector
operating most TV sets,VCRs or Sat-Receivers.4 for the product being operated should flash2. Press the Volume Up button $and note
briefly. If the Device Control Selector flashes forthat.the Program/SPL Indicator 2 will stop
For some products, however, the function of asome but not all buttons for a particular product,flashing and stay amber.
particular button does not follow the command
it does NOT indicate a problem with the remote,
printed on the remote. In order to see whichbut rather that no function is programmed for3. Press either the AVR Selector 5 or the
function a button controls, consult the Functionthe button being pushed.Input Selector 4, depending on which sys-
List tables printed on page 44.To use thosetemOs volume control you wish to have attached
Y The remote was pre-programmed with codes
tables, first check the type of device being con-for the punch-through mode.The Program/SPL
trolled (e.g.,TV,VCR). Next, look at the remotefor units of the latest generation, but some codesIndicator 2 will blink green three times and
may differ from those needed for earlier units.
control diagram or page 44. Note that each but-then go out to confirm the data entry.
ton has a number on it.When your device doesnOt react as listed in theExample: To have the AVROs volume control acti-
function list (page 44/45), let the AVR5000
To find out what function a particular button hasremote learn the appropriate codes from thevated even though the remote is set to control
for a specific device, find the button number onthe TV, first press the Video/TV Input Selector
original remote (learning codes see page 40).
the Function List and then look in the column for4 and the Mute button at the same time.
the device you are controlling. For example, but-Next, press the Volume Up button $, followed
ton number 54 is the Macro 2 button for theby the AVR Input Selector 5.
AVR5000, but it is the OFavorite� button for
many cable television boxes and satelliteNOTE: Should you wish to return the remote to
the original configuration after entering a Volume
receivers. Button number 32 is the Delay buttonPunch-Through, you will need to repeat the steps
for the AVR5000, but the Open/Close button for
CD players.shown above. However, press the Video/TV
Input Selector in steps one and three.
Note that the numbers used to describe the but-
ton functions at the left for the purposes of
describing how a button operates are a different
set of numbers than those used in the rest of this
manual to describe the button functions for the
AVR 5000.
42 PROGRAMMING THE REMOTE |
ACEC
